Installing Floating Cabinets – Types of Floating Shelf

A floating shelf is a shelf that has no visible mounting or helps showing and appears as whether it is “floating” on the wall.

Types of Floating Shelf

If you need to fit a shelf of this type you’ve a number of options:

Make your own: It is possible to make your own floating shelf from just a few fundamental materials. Though we don’t but have a project on this (we’ve one in the pipeline) there are a number of good guides on-line, considered one of which may be found here.

Buy a pre-made kit: As I’m positive you will be aware, pretty much every homestore, supermarket and DIY shed will stock a floating shelf kit. The kit usually includes a wooden shelf part and a bracket. The bracket fixes to the wall and the shelf slides on

To these ends, in this project we are going to cover fixing a floating shelf kit to a wall.

Types of Wall Fixings for Floating Cabinets

The first job is to check the development of the wall and from here you’ll then know what type of fixings you’ll need:

Strong brick or masonry wall: For this you will want red wall plugs (for six – 10mm screws). If you happen to would more information see our fixing to masonry partitions project here

Plasterboard and studwork wall: Ideally one of the best answer is to find the vertical studs within the wall and screw directly into these though generally this isn’t possible. In these instances you will want to make use of either a Redidrive, spring toggle or nylon toggle fixing (as these are typically the very best at supporting weight). For information on how to use these fixings see our fixing to plasterboard project

Fixing a Floating Shelf to a Wall

Once you have determined your wall type and have acquired the correct fixings for use you’ll be able to progress to installing. For the purposes of this project we will probably be fixing to a stable masonry wall so we’ll run by way of this process and cover related information for different fixings where required.

Check the Area with a Stud Detector

Earlier than drilling any holes it is a good suggestion to run over the world you’re going to be drilling into with a stud, pipe and cable detector. This is a helpful gadget that detects any pipes or wires that could be buried within the wall so that you simply don’t inadvertently drill by means of them. Not only is this doubtlessly deadly however additionally it is very costly!

Locating Plasterboard Vertical Studwork

After running over your installation area with the stud detector to check for wires and pipes the next activity is to drill your fixing holes. If you’re fixing to a plasterboard wall, as said on the prime of this project, essentially the most stable fixing is to screw straight into the vertical upright stud timbers.

You need to use the affore talked about detector to locate the sides of the studs and after you have, mark the sides on the wall with a pencil so that you already know exactly where the studs are.

Regardless of what surface you are fixing to you’ll need to drill some holes. Firstly, take your bracket and position it on the wall in the location that you really want your shelf.

Using a pencil, mark the highest left fixing hole so that you recognize the place to drill. Put the bracket to on side for now. Once more, relying on what you need to drill, choose the right drill bit from the list beneath:

Masonry wall: For this you have to a 6mm masonry drill bit

Plasterboard and studwork: In case you are screwing into the stud then you will want to drill a small pilot hole. For this use a 2.5 – 3mm universal or multi-function drill bit. If you are drilling into the plasterboard, the drill bit required will rely on the type of fixing you are using. This should be stated on the packaging

Insert the require drill bit into a drill (will be either corded or twineless) and position the tip of the bit directly on the mark you made on the wall. Start the drill off slowly and enhance in pace as the bit bites into the surface. Drill to the required depth and then pull the drill bit out

Inserting the First Fixing

Before inserting the wall plug its a good idea to vacuum out the mud after which take certainly one of your red wall plugs and push it into the hole. If it doesn’t go all the best way in, tap it in with a hammer.

Once the wall plug is in place, take your bracket and position the highest left fixing hole over the wall plug, insert a screw and screw it up, but not all the way. Guantee that the bracket can swing freely as you will have to move it around.

By way of what screws to use, for this job we have used four x 30mm screws, maybe somewhat oversized but when they’re slightly bigger you can be sure that they may drive the wall plug to develop and chew into the wall giving it a very good anchor.

If you are you looking for more info about Support Brackets look at the web site.